manualshive.com logo in svg

Lamtec ETAMATIC, Руководство пользователя

Поделиться
Скачать
Lamtec ETAMATIC Скачать руководство пользователя страница 55

54

7 

 Internal Burner Firing-rate Controller

7.9

Control by Atmospheric Condition

If the burner firing-rate controller is configured as "controlled by atmospheric conditions" the 
setpoint value can be shifted between the parameterised setpoint minimum and setpoint max-
imum by connecting another PT 100 temperature sensor to the terminals 39, 40 and 41. In the 
realize by atmospheric conditions, the outside temperature is a component of setpoint calcu-
lation. This allows the operator to enter a minimum and a maximum setpoint, between which 
the outside temperature can determine the final setpoint value.

Fig. 7-1 Control by atmospheric conditions

With the option "Control by atmospheric condition" you may realise an external setpoint pre-
setting.

7.10

Set Point Changeover

You can switch the setpoint with the input "setpoint switchover". If you use a version with fixed 
setpoint value it is possible to select one of the two values, which are entered in the parame-
ters 796 and 798 with this contact.
If you have activated the control by atmospheric conditions additionally, you can select be-
tween two pairs of limit values (see control by atmospheric conditions and limit ranges). The 
parameters for setpoint 1 (for setpoint switching) and setpoint min. 1 (for control by atmo-
spheric conditions) are equal. Likewise the parameters setpoint 2 and setpoint min. 2. The cor-
responding content is assigned according to the configuration.
When activating the "control by atmospheric conditions” option and setting the adjustable pa-
rameters, you may realise an external setpoint default. In other words, the setpoint can be ad-
justed manually or automatically via a potentiometer (or switched through resistors). By 
connecting a change-over switch, you can implement a night-time reduction instead of control 
by atmospheric conditions. A control by atmospheric conditions and a night-time reduction can 
be realised simultaneously, if you combine the control by atmospheric conditions with the set-
point switching.

Содержание ETAMATIC









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды