manualshive.com logo in svg

Lamtec ETAMATIC, Руководство пользователя

Поделиться
Скачать
Lamtec ETAMATIC Скачать руководство пользователя страница 13

12

2  

Safety

2.3

Associated Automatic Flame Guard

The unit is available with and without an integral flame guard. Sensor types FFS 06, FFS 05 
and FFS 05UV can be connected to the integral flame guard. When used without integral 
flame guard, any tested flame guard in accordance with DIN EN 298 and/or DIN EN 230 and 
approval for continuous operation may be connected to terminal 53 like the following (docu-
ment no. in brackets):
Compact flame detector F200 K1 and K2 (DLT7620) or the flame guards F150 (DLT7521) and 
F250 (DLT7540) with the flame sensors FFS05 / FFS05 EX / FFS05 ExI (DLT7501 and 
DLT7503) and FFS06 (DLT7502)

WARNING!
If the ETAMATIC is used with an integral flame guard, terminal 53 must not be connected to 
any other components.

WARNING!
Electrical connection to appliances not listed in these instructions: only after consultation with 
the manufacturers or a qualified expert.

If a flame guard, which is not approved for continuous operation, is connected, the approval 
of the system for continuous operation expires.
Liability for proper functioning of the unit passes to the owner or operator.
If the unit is incorrectly operated, serviced or repaired by unqualified personnel, or if operation 
is inconsistent with the specified intended purpose, liability for the unit’s correct functioning in 
each case passes to the owner or operator.)

WARNING!
The type approval lapses in the event of modifications to the unit. The unit's inputs and outputs 
must only be wired according to the specifications in these instructions.

LAMTEC GmbH & Co KG will not be liable for damage or injury arising out of a failure to ob-
serve the instructions above. The warranty and liability provisions contained in LAMTEC 
GmbH & Co KG’s terms and conditions for and Supply, shall not be extended by virtue of the 
instructions above.
Where reference is made to legislation, government regulations and standards, these are 
based on the legal system of the Federal Republic of Germany.

Содержание ETAMATIC









































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды