La San Marco 95 Series, Руководство по эксплуатации и обслуживанию

Страница: 45 / 115

43
ENGLISH
F O R T H E U S E R
These models are provided with a panel with a button strip and a lighted display installed on the lower part of the working area
(
91 , in the figure on page 45). The services that can be obtained from this panel are:
- PROGRAMMING: CLOCK, ON, OFF, HOLIDAYS, REGENERATION OF WATER SOFTENER
- MACHINE STARTING AND STOPPING: MANUAL OR AUTOMATIC (if programmed)
- DISPLAY OF COUNTS FOR COFFEE, TEA, WATER SOFTENER, etc.
- EMERGENCY OPERATION
In addition, the button strip used for hot water serving has a second display incorporated
48 in it, which is used to show the
temperature and pressure of the water in the boiler.
The serving of steam and hot water, as well as the coffee servings, are made as already described on page 41.
Programming on panel 91
Check that the water in the tank is held at a regular level and turn the main switch 30 to position 2.
In programming, the buttons on panel 91 have the following meanings:
“THE” (set) PUSH BUTTON: ENTER PROGRAMMING AND ADVANCE TO THE VARIOUS STEPS
BUTTON “1”(-) : DECREASE
BUTTON “2”(+) : INCREASE
BUTTON “E”(end) : EXIT FROM PROGRAMMING
More specifically, programming is entered by pressing the “THE” (set) button. The first impulse gives access to function 0 (the
function number is shown, flashing red, on the display). The HOURS and MINUTES of the clock are set through function 0,
using either the “1”(-) or “2”(+) buttons. Pressing the “THE” (set) button again accesses function 1, which allows the setting of
the days of the week through buttons “1”(-) and “2”(+).
In this manner it is possible to program all the available functions, which are summarized in the following table:
indications on display 91 function limits meaning
HH - MM 0 0,00 - 23.59
DAY OF WEEK 1 1 - 7
DATE SETUP 2 1 - 31
MONTH SETUP 3 1 - 12
YEAR SETUP 4 00 - 99
CLOSE DAY 5 0 - 99
AM OPEN TIME 6 0.00 - 23.50
AM CLOSE TIME 7 0.00 - 23.50
AM OPEN DAY 8 1 - 7 NO-YES
PM OPEN TIME 9 0.00 - 23.50
PM CLOSE TIME A 0.00 - 23.50
PM OPEN DAY B 1 - 7 NO-YES
RIGEN SETUP C 1 - 250
Functions 8 and B are programmed using key “2” to change the day from 1 to 7 and key “1” to switch NO/YES
(NO = CLOSURE - YES = OPENING).
To leave the programming mode, at any moment, it is sufficient to press the “E” button.
Normal operation
During the automatic operation, the machine is controlled by an electronic control unit and it is active when the led of button
“E” is off (see panel
91 ). In this condition, by pressing button “1” I/O (ON/OFF) for 5 seconds, it is possible to have the
manual START and STOP of the machine, excluding the automatic ON and OFF control.
THE FOLLOWING OPERATING MODES ARE POSSIBLE
ON
The machine is active and working when the display on the panel
91 shows the time of day and the day of the week.
ADDITIONAL NOTES FOR
95-26 AND 95-36 MODELS
HOURS AND MINUTES ON CLOCK
DAY OF WEEK
DATE (DAY OF MONTH)
MONTH
YEAR
HOLIDAYS (0 = OFF)
OPENING TIME I (AM)
CLOSING TIME I (AM)
DAYS OPEN I (AM)
OPENING TIME II (PM)
CLOSING TIME II (PM)
DAYS OPEN II (PM)
(CYCLES x 100) FOR REGENERATION