Kollmorgen AKD series Скачать руководство пользователя страница 5

Страница: 5 / 216

9.5.1 Connector assignment AKD-x00306, AKD-x00606

9.5.2 Connection diagram AKD-x00306, AKD-x00606

9.5.3 Connector assignment AKD-x01206

9.5.4 Connection diagram AKD-x01206

9.5.5 Connector assignment AKD-x02406 and AKD-x00307 to 02407

9.5.6 Connection diagram AKD-x02406 and AKD-x00307 to 02407

9.5.7 Connector assignment AKD-x04807

9.5.8 Connection diagram AKD-x04807

9.6 Connection Overview AKD-M

9.6.1 Connector assignment AKD-M00306, AKD-M00606

9.6.2 Connection diagram AKD-M00306, AKD-M00606

9.6.3 Connector assignment AKD-M01206

9.6.4 Connection diagram AKD-M01206

9.6.5 Connector assignment AKD-M02406, AKD-M00307 to AKD-M02407

9.6.6 Connection diagram AKD-M02406, AKD-M00307 to AKD-M02407

9.6.7 Connector assignment AKD-M04807

9.6.8 Connection diagram AKD-M04807

9.7 EMI Noise Reduction

9.7.1 Recommendations for EMI noise reduction

9.7.2 Shielding with external shielding busbar

100

9.7.2.1 Shielding Concept

100

9.7.2.2 Shielding Busbar

101

9.7.3 Shielding connection to the drive

102

9.7.3.1 Grounding plates

102

9.7.3.2 Shield connection clamps

102

9.7.3.3 Motor connector X2 with shielding connection

102

9.8 Electrical Supply Connection

103

9.8.1 Connection to various mains supply networks AKD-xzzz06 (120V to 240V)

103

9.8.2 Connection to various mains supply networks AKD-xzzz07 (240V to 480V)

104

9.8.3 24 V auxiliary supply (X1)

105

9.8.3.1 AKD-x003 to 024, connector X1

105

9.8.3.2 AKD-x048, connector X1

105

9.8.4 Mains supply connection (X3, X4)

106

9.8.4.1 Three phase connection (all AKD types)

107

9.8.4.2 Single/Dual phase connection (AKD-x00306 to AKD-x01206 only)

107

9.9 DC Bus link (X3, X14)

108

9.9.1 DC Bus topology with Y connectors (24 A max.)

109

9.9.2 DC Bus topology with busbar

109

9.9.3 External regen resistor (X3)

110

9.9.3.1 AKD-x003 to 024, regen connector X3

110

9.9.3.2 AKD-x048, regen connector X3

111

9.9.4 Capacitor Modules (X3)

112

9.9.4.1 Technical Data

112

9.9.4.2 Example installation with KCM-S and KCM-E

113

9.9.4.3 Example installation with KCM-P and KCM-E

114

9.9.4.4 Discharging KCM modules

115

9.10 Motor Power Connection (X2)

116

9.10.1 AKD-x003 to 024, power connector X2

117

9.10.2 AKD-x048, power connector X2

117

9.11 Motor Brake Connection (X2, X15, X16)

118

9.11.1 AKD-x003 to 024, bBrake connector X2

118

9.11.2 AKD-x048, brake connectors X15, X16

119

9.11.3 Functionality

120

9.12 Feedback Connection (X10, X9, X7)

121

AKD Installation | Table of Contents

Kollmorgen | kdn.kollmorgen.com | October 2017

Содержание AKD series

























































































































































































































Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды

Kollmorgen AKD series, Руководство по установке

Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды