manualshive.com logo in svg

Kollmorgen AKD series, Руководство по установке

Серия приводов Kollmorgen AKD - это надежные и эффективные устройства для автоматизации производства. Вы можете бесплатно скачать руководство по эксплуатации на manualshive.com. Получите подробную информацию о настройке и использовании продукта, чтобы оптимизировать свой бизнес.

Поделиться
Скачать
background image

9.15 LED display

The LED seven-segment display indicates the status of the drive after the 24 V supply is
switched on. If the service connection to the PC or to the PAC doesn't work, then the LED
display is the only way to get information.

AKD two digits

AKD-M two + one digits

AKD fault codes or warning codes
are displayed constantly if present.
Fault messages are coded with "F"
or "E", warnings are coded with
"n". The IP address can be flashed
across the LED display if the B1
button is pressed.

The two digits LED display indicates the AKD mes-
sages. Fault messages are coded with "F", warnings
are coded with "n".
The one digit LED indicates the PDMM messages of
the AKD PDMM. Error messages are coded with "E",
warnings (alarms) are coded with "A". Status of applic-
ation programs are indicated as well. With push-but-
tons B2 and B3 a menu with several functions can be
started (

➜

# 168).

See WorkBench Onlinehelp for details.

Display Codes

(overview)

Status

o0, o1, o2 ...

Normal operation, operation mode 0 or 1 or 2 ..., no faults

Fx

Fault (see (

➜

# 202)

nx

Warning (see (

➜

# 202)

IPx

Displaying drive IP address

- -

Powered on and FPGA loading. If continuous then operational and
resident FPGA images are corrupt.

[.]

Drive enabled

[.] (flashing)

Drive in an internal dynamic brake mode (DRV.ACTIVE = 3).

dx

Firmware download

AKD Installation | 9   Electrical Installation

Kollmorgen | kdn.kollmorgen.com | October 2017

165

Содержание AKD series

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AKD series

Cambridge Audio Azur 840E Quick Start preview
Azur 840E
Бренд: Cambridge Audio Страницы: 2
Cambridge Audio AZUR 851C Quick Start Manual preview
AZUR 851C
Бренд: Cambridge Audio Страницы: 19
Cambridge Audio Edge NQ Manual preview
Edge NQ
Бренд: Cambridge Audio Страницы: 14
NAD M33 Quick Setup Manual preview
M33
Бренд: NAD Страницы: 2
Cambridge Audio Topaz AM10 Quick Start Manual preview
Topaz AM10
Бренд: Cambridge Audio Страницы: 19
Fender 410 PRO Operating Instructions Manual preview
410 PRO
Бренд: Fender Страницы: 12
Lab.gruppen FP+ Series FP 10000Q Technical Data preview
FP+ Series FP 10000Q
Бренд: Lab.gruppen Страницы: 2
Marshall Amplification JMP-1 Handbook preview
JMP-1
Бренд: Marshall Amplification Страницы: 12
YachtConnect IT1004 User And Installation Manual preview
IT1004
Бренд: YachtConnect Страницы: 24
PRO SIGNAL PSG03638 User Manual preview
PSG03638
Бренд: PRO SIGNAL Страницы: 5
Russco Fidelity-master Manual preview
Fidelity-master
Бренд: Russco Страницы: 14
Harman JBL PARTYBOX710 Quick Start Manual preview
JBL PARTYBOX710
Бренд: Harman Страницы: 26
Laney GH100TI Operating Instructions Manual preview
GH100TI
Бренд: Laney Страницы: 16
JL Audio 94556 Installation Manual preview
94556
Бренд: JL Audio Страницы: 10
ATEN KVMP CM1164 Quick Start Manual preview
KVMP CM1164
Бренд: ATEN Страницы: 2
Cyfre CA-819 Installation Manual preview
CA-819
Бренд: Cyfre Страницы: 2
Focusrite iTracker One Pre User Manual preview
iTracker One Pre
Бренд: Focusrite Страницы: 15
Monacor WAP-3 Instruction Manual preview
WAP-3
Бренд: Monacor Страницы: 18

Бренды по названию

Популярные бренды

Загрузить еще бренды