Kollmorgen AKD series Скачать руководство пользователя страница 207 | Manualshive

Страница: 207 / 216

background image

10.4.2 Additional fault messages AKD-T

AKD BASIC runtime faults are displayed in the two-digits 7-segment display of the drive:

The two digits LED display
indicates the fault code.

The additional runtime fault messages for AKD-T are coded with numbers starting from F801.
Remedy for all errors: clear error, fix user program, recompile, download and attempt to run
the program again.

Eliminate errors and faults in compliance with work safety rules. Troubleshooting only by
qualified and trained staff.

More information about error messages, causes, remedy and clearing errors can be found in
the WorkBench online help and in

.

Error

Description

F801

Divide by zero.

F802

Stack Overflow.

F803

Insufficient Memory.

F804

No interrupt handler defined.

F805

Interrupt error.

F806

Max string length exceeded.

F807

String overflow.

F808

Array out of bounds.

F809

Feature not supported.

F810

Internal firmware/hardware error.

F812

Parameter not supported.

F813

Parameter access error.

F814

Data not found.

F815

Data invalid.

F816

Data too high.

F817

Data too low.

F818

Param type out of range.

F819

Data not divisible by 2.

F820

Invalid position modulo setting.

F821

Cannot read from command.

F823

Enable Drive first.

F824

DRV.OPMODE must be 2 (position).

F825

DRV.CMDSOURCE must be 5 (program).

F826

Cannot execute during a move.

F827

Writing to read-only parameter.

F828

Disable Drive first.

F829

Opcode not supported - upgrade firmware.

F830

No negative values allowed.

F831

BASIC program is invalid. May need firmware upgrade.

F832

BASIC program is missing.

F901

Too many cams.

AKD Installation | 10 Setup

Kollmorgen | kdn.kollmorgen.com | October 2017

207

«
...
205
206
207
208
209
...
»

Содержание AKD series

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для AKD series

Бренд: NAD Страницы: 2

Бренд: OM POWER Страницы: 13

Бренд: Vanguard Dynamics Страницы: 3

fP Series FP 6400

Бренд: Lab.gruppen Страницы: 2

Бренд: T&M Performance Страницы: 11

Бренд: Waterfall Audio Страницы: 34

Бренд: Fuba Страницы: 19

Бренд: Sonifex Страницы: 22

JL7 Black Path Edition

Бренд: C.A.T. Страницы: 9

Бренд: Black Rooster Audio Страницы: 4

Бренд: Knoll Страницы: 8

Бренд: PROEL Страницы: 12

Бренд: STAX Страницы: 8

Бренд: ORANGE Страницы: 11

THUNDERBASS BT-350

Бренд: Crate Страницы: 12

Бренд: e-audio Страницы: 4

Бренд: Denon Страницы: 175

Бренд: PROception Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды