Kollmorgen AKD series Скачать руководство пользователя страница 205

Страница: 205 / 216

Code

Message/Warning

F479, n479

Wake & Shake - Loop angle delta too large.

F480

Wake & Shake - Fieldbus command velocity too high.

F481

Wake & Shake - Fieldbus command velocity too low.

F482

Wake & Shake - Commutation not initialized.

F483

Wake & Shake - Motor U phase missing.

F484

Wake & Shake - Motor V phase missing.

F485

Wake & Shake - Motor W phase missing.

F486

Input change rate exceeds maximum speed of emulated encoder.

F487

Wake & Shake - Validating positive movement Failed.

F489

Wake & Shake - Validating negative movement Failed.

F490

Wake & Shake - Validating commutation angle timed out.

F491

Wake & Shake - Validating commutation angle moved too far - bad comm
angle.

F492

Wake & Shake - Validating commutation angle required more than
MOTOR.ICONT.

F493

Invalid commutation detected – motor accelerating in the wrong direction.

n495

Failed to process recorded cogging compensation table.

F501, n501

Bus over voltage.

F502

Bus under voltage. Warning issued prior to fault.

F503, n503

Bus capacitor overload.

F504 to F518 Internal supply voltage fault

F519

Regen short circuit.

F521, n521

Regen over power.

F523

Bus over voltage FPGA

F524, n524

Drive foldback.

F525

Output over current.

F526

Current sensor short circuit.

F527

Iu conversor digital analógico atual preso.

F528

Iv conversor digital analógico atual preso..

F529

Iu current offset limit exceeded.

F530

Iv current offset limit exceeded.

F531

Power stage fault.

F532

Drive motor parameters setup incomplete.

F534

Failed to read motor parameters from feedback device.

F535

Power-board over-temperature fail.

F560

Regen near capacity, could not prevent over voltage.

F570, n570

Mains phase loss.

n580

Using derivate of position with sensorless feedback type in position mode.

n581

Zero velocity with induction sensorless feedback type in position mode.

n582

Velocity has been limited, commutation frequency max. 599 Hz to meet
ECCN-3A225 / AL-3A225 limits.

n601

Modbus data rate is too high.

F602

Safe torque off.

n603

OPMODE incompatible with CMDSOURCE

n604

EMUEMODE incompatible with DRV.HANDWHEELSRC.

F621

Control Board CRC fault.

AKD Installation | 10 Setup

Kollmorgen | kdn.kollmorgen.com | October 2017

205

Содержание AKD series

























































































































































































































Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды

Kollmorgen AKD series, Руководство по установке

Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды