Kollmorgen AKD series Скачать руководство пользователя страница 204

Страница: 204 / 216

AKD Installation | 10 Setup

Code

Message/Warning

F303

Run away.

F304, n304

Motor foldback.

F305

Brake open circuit.

F306

Brake short circuit.

F307

Brake applied during enable state.

F308

Voltage exceeds motor rating.

n309

Motor I²t load.

F312

Brake released when it should be applied.

F401

Failed to set feedback type.

F402

Analog signal amplitude fault.

F403

EnDat communication fault.

F404

Illegal Hall state (111, 000).

F405

BiSS watchdog fault.

F406

BiSS multicycle fault.

F407

BiSS sensor fault.

F408 to F416 SFD feedback fault.

F417

Broken wire in primary feedback.

F418

Primary feedback power supply.

F419

Encoder init procedure failed

F420

FB3 EnDat Communications Fault.

F421

SFD position sensor fault

F423

Non volatile memory failure - Extended Multiturn

F436

EnDat overheated.

F438, n438

Deviation from predicted trajectory fault.

F439, n439

Following error (magnitude).

F450

Following error (presentation).

F451, n451

Tamagawa encoder: battery.

F452

Extended multiturn not supported with this feedback.

F453 to F459 Tamagawa encoder: communication.

F460

Tamagawa encoder: over speed.

F461

Tamagawa encoder: counting Error.

F462

Tamagawa encoder: counting overflow.

F463

Tamagawa encoder: overheat.

F464

Tamagawa encoder: multiturn error.

F465

Excessive shock detected by feedback device.

F467

Feedback fault on feedback 1 (see FB1.FAULTS for details). In case of
BiSS: communications.

F468

FB2.SOURCE not set, remote commutation not possible.

F469

FB1.ENCRES is not power of two, remote commutation not possible.

F470

Feedback fault on feedback 3.

F471

Operation in Position Mode with Halls Only feedback not allowed.

F473

Wake & Shake - Insufficient movement

F475

Wake & Shake - Excess movement.

F476

Wake & Shake - Fine-coarse delta too large.

F478, n478

WWake & Shake - Over speed.

204

Kollmorgen | kdn.kollmorgen.com | October 2017

Содержание AKD series

























































































































































































































Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды

Kollmorgen AKD series, Руководство по установке

Результаты поиска

Содержание AKD series

Отзывы:

Похожие инструкции для AKD series

Бренды по названию

Популярные бренды