Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 84

Страница: 84 / 118

Heinrichs Messtechnik GmbH

Page 84 of 118

OPERATING MANUAL TMU-W / UMC4

7.2.10.2

Current output I1 alarm

This function allows the operator to define the state taken on by the current output when a state of alarm is
detected. This information can be analysed in the control system. Press “Enter” to display the current setting:

I1 : alarm

[>22mA]

The current assignment will be displayed and can be changed by toggling the arrow keys.
The operator can choose between the following settings:



not used

no alarm function



> 22 mA

current rise in the case of an alarm



< 3.8 mA

current reduction in the case of an alarm

Pressing the “Enter” key confirms the entry

7.2.10.3

Current output I1 assignment

This function allows the operator to define the measured value to be output as an analogue signal via current
output I1. When devices with HART

communication capabilities are used, current output I1 is usually assigned

to mass flow. Press “Enter” to display the current setting.

I1 assigned to

[Mass flow]

The current assignment will be displayed and can be changed by toggling the arrow keys.
The operator can choose between the following settings:



Mass flow



Volume flow



Density



Temperature

Pressing the “Enter” key confirms the entry

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Результаты поиска

Содержание Heinrichs Coriolis Mass Flow Meter

Отзывы:

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренды по названию

Популярные бренды

Kobold Heinrichs Coriolis Mass Flow Meter, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Heinrichs Coriolis Mass Flow Meter

Отзывы:

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренды по названию

Популярные бренды