Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 52 | Manualshive

Страница: 52 / 118

background image

Heinrichs Messtechnik GmbH

Page 52 of 118

OPERATING MANUAL TMU-W / UMC4

7.2.1.13

Display mode during startup

By choosing the Display mode during startup function the operator can define the default display. After the
operator switched the device on and did not touch any keys for a longer period of time, the defined default
display will be shown:

Display mode

[QM]

One of the following default displays can be selected.



QM (Mass flow)



QV (Volume flow)



Counter f(orward)



Counter r(everse)



Density



Temperature



QM + Counter f



QM + Density



QM + Temperature



QV + Counter f



QV + Density



and Raw values

7.2.1.14

Raw values

The “Raw values display” supports fault diagnosis and trouble shooting. Please inform our service department
about the clear text error messages and the contents of this “Raw values display.”

xxx.xxx ttt.tttt

fff.ffff eee.aaa

The displayed values have the following meaning:

xxx.xxx: Measure for the phase displacement between the sensor signals.
ttt.ttt:

Indicates the measured sensor temperature.

fff.ffff:

Indicates the current oscillation frequency of the system.

eee.aaa: Indicates the value of the excitation current (eee) and the sensor voltage (aaa).

«
...
50
51
52
53
54
...
»

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Отзывы:

Нет отзывов

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренд: Kawai Страницы: 2

Бренд: Datron Страницы: 197

Бренд: Kane Страницы: 4

Goldmann AT 870

Бренд: Haag-Streit Страницы: 20

Бренд: ICM Controls Страницы: 8

Бренд: janitza Страницы: 12

Бренд: janitza Страницы: 84

Бренд: janitza Страницы: 6

Бренд: janitza Страницы: 14

Бренд: janitza Страницы: 98

Бренд: Supertech agroline Страницы: 10

Бренд: Chauvin Arnoux Страницы: 44

Бренд: Droplet Страницы: 35

Бренд: Sencore Страницы: 75

Бренд: truflo Страницы: 33

Бренд: A-CUBE Страницы: 25

Бренд: Omega Страницы: 4

Бренд: Racelogic Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды