Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 87 | Manualshive

Страница: 87 / 118

background image

Heinrichs Messtechnik GmbH

OPERATING MANUAL TMU-W / UMC4

Page 87 of 118

SIMULATION functional class

The functional class SIMULATION is comprised of the functions for simulating the outputs. If simulation is
activated, all output signals will be generated based on the selected type of simulation. The peripherals
connected to the device can be tested without a flowing product.

Simulation will be deactivated automatically if the operator switched the device off or did not touch any control
unit keys for about 10 minutes. Simulation can also be activated and controlled via HART

®

commands.

SIMULATION

Simulation

on / off

Simulation

status output

SIMULATION

functional class

Simulation

[off]

_________________

on
off

Status output

[on]

_________________

on
off

Simulation

pulse output

Set frequency

0009.0 Hz

Simulation

curr. output I1

Simulation

curr. output I2

Set I1

I1 = 12.00 mA

Set I2

I2 = 12.00 mA

Simulation

direct / QMabs

Simulation

[direct]

_______________

direct

QM, D, T

Simulation

QMabs

Set QMabs

+0900.000 kg/h

Simulation

density

Set density

0500.000 g/l

Simulation

temperature

Set temperature

+090 °C

«
...
85
86
87
88
89
...
»

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Отзывы:

Нет отзывов

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренд: Parker Research Corp Страницы: 3

Бренд: A&D Страницы: 74

Бренд: WAGER Страницы: 36

Бренд: Eagle Eye Страницы: 3

Бренд: VALTRONICS Страницы: 13

Бренд: JIANGSU Страницы: 8

Бренд: WATERGUARD Страницы: 2

CoolPoint CP12-V8

Бренд: UFM Страницы: 14

Nitro-Save NS16

Бренд: TDI Страницы: 4

Бренд: Teledyne Страницы: 85

Бренд: Power Measurement Страницы: 20

Бренд: 4iiii Страницы: 35

Бренд: E+E Elektronik Страницы: 9

Thruline 4020 Series

Бренд: Bird Electronic Страницы: 59

Бренд: QUNDIS Страницы: 6

Бренд: Skil Страницы: 80

Бренд: Radiation Alert Страницы: 22

Бренд: B&K Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды