Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 63 | Manualshive

Страница: 63 / 118

background image

Heinrichs Messtechnik GmbH

OPERATING MANUAL TMU-W / UMC4

Page 63 of 118

7.2.5.3

Mass flow QM range

This function allows the operator to set the upper-range value for mass flow. The upper-range value takes on
the unit defined using the Mass flow unit function. The upper-range value will scale the current and frequency
outputs assigned to mass flow. After choosing the Mass flow QM range function and pressing “Enter”, the
following selection field will be displayed:

QM range=100%

XXXXX.XX kg/h

The current upper-range value for mass flow will be displayed and can be changed by toggling the arrow keys.
Pressing the “Enter” key confirms the entry.

7.2.5.4

Mass flow QM limit MIN

The MIN limiting value for mass flow can be evaluated via the status output. You enter the value as a
percentage of the set upper-range value. If the mass flow is lower than that limit value, the status output will
be set in case the corresponding assignment has been made. If the alarm function has also been activated for
the assigned current output, the applied current will change to < 3.2 mA or > 20.5 mA / 22 mA. After choosing
the Mass flow QM limit MIN function and pressing “Enter”, the following selection field will be displayed:

Mass flow limit

MIN = 10 %

The current MIN upper-range value for mass flow will be displayed and can be changed by toggling the arrow
keys.
Pressing the “Enter” key confirms the entry.

7.2.5.5

Mass flow QM limit MAX

The MAX limiting value for mass flow can be evaluated via the status output. You enter the value as a
percentage of the set upper-range value. If the mass flow surpasses this limit value, the status output will be
set in case the corresponding assignment has been made. If the alarm function has also been activated for the
assigned current output, the applied current will change to < 3.2 mA or > 20.5 mA / 22 mA. After choosing the
Mass flow QM limit MAX function and pressing “Enter”, the following selection field will be displayed:

Mass flow limit

MAX = 90 %

The current MAX upper-range value for mass flow will be displayed and can be changed by toggling the arrow
keys.
Pressing the “Enter” key confirms the entry.

«
...
61
62
63
64
65
...
»

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Отзывы:

Нет отзывов

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренд: Banner Страницы: 11

Бренд: Bante Instruments Страницы: 10

Бренд: BANTE Страницы: 11

Бренд: Banner Страницы: 14

Бренд: Banner Страницы: 16

Бренд: Oceanic Страницы: 17

NANOCOLOR Advance

Бренд: Macherey-Nagel Страницы: 45

Бренд: janitza Страницы: 48

Бренд: S.E. International Страницы: 30

Бренд: SZBJ Страницы: 2

Бренд: Lutron Electronics Страницы: 20

Бренд: Rion Страницы: 4

Бренд: LaMotte Страницы: 32

Бренд: R&S Страницы: 130

LiveTester LT 220

Бренд: StarLogixs Страницы: 7

Combo meter P700 Pro

Бренд: AquaMaster Страницы: 20

Бренд: Xylem Страницы: 39

Бренд: Vector Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды