Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 85 | Manualshive

Страница: 85 / 118

background image

Heinrichs Messtechnik GmbH

OPERATING MANUAL TMU-W / UMC4

Page 85 of 118

7.2.10.4

Current output I2 4 to 20 mA

The “Current output I2 4 to 20 mA” function allows the operator to define the range in which the current output
is to be operated. The range of 4 to 20.5 mA follows the NAMUR recommendation and covers the range from 0
to 104 % of the measuring range. The standard range of 4 to 21.6 mA allows for a control of the measuring
range of up to 110 %.
Press “Enter” to display the current setting.

Current output I2

[4] – 21.6 mA

The current assignment will be displayed and can be changed by toggling the arrow keys.
The operator can choose between the following settings:



4 – 20.5 mA



4 – 21.6 mA

Pressing the “Enter” key confirms the entry

7.2.10.5

Current output I2 alarm

This function allows the operator to define the state taken on by the current output when a state of alarm is
detected. This information can be analysed in the control system. Press “Enter” to display the current setting.

I2 : alarm

[not used]

The current assignment will be displayed and can be changed by toggling the arrow keys.
The operator can choose between the following settings:



not used

no alarm function



> 22 mA

current rise in the case of an alarm



< 3.8 mA

current reduction in the case of an alarm

Pressing the “Enter” key confirms the entry.

«
...
83
84
85
86
87
...
»

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Отзывы:

Нет отзывов

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренд: X-laser Страницы: 17

Бренд: Dwyer Instruments Страницы: 189

Бренд: Lowrey Страницы: 109

Бренд: THORLABS Страницы: 21

Бренд: Trotec Страницы: 14

Бренд: East Tester Страницы: 27

Бренд: Konica Minolta Страницы: 48

Бренд: SMPE Страницы: 2

Бренд: Banner Страницы: 4

Бренд: Hanna Instruments Страницы: 21

Бренд: Ditel Страницы: 2

Бренд: R&S Страницы: 100

Бренд: E Instruments Страницы: 64

InfiniiMax III+ Series

Бренд: Keysight Страницы: 162

Бренд: Level Pro Страницы: 59

Бренд: VOLTCRAFT Страницы: 4

Бренд: OHAUS Страницы: 2

Бренд: Selecta Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды