Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 118

background image

Heinrichs Messtechnik GmbH

OPERATING MANUAL TMU-W / UMC4

Page 75 of 118

7.2.7.4

Temperature limit MIN

The MIN limiting value for temperature can be evaluated via the status output. This value is entered in the set
temperature unit.

After selecting the Temperature limit MIN function, press “Enter” to display the following selection field:

MIN temperature

-010 °C

The current MIN limiting value will be displayed and can be changed by toggling the arrow keys. If the measured
value falls below the limiting value, the “Alarm” status message will be displayed
Pressing the “Enter” key confirms the entry.

7.2.7.5

Temperature limit MAX

The MAX limiting value for temperature can be evaluated via the status output. This value is entered in the set
temperature unit.

After selecting the Temperature limit MAX function, press “Enter” to display the following selection field

MAX temperature

+ 250 °C

The current MAX limiting value will be displayed and can be changed by toggling the arrow keys. If the
measured value falls below the limiting value, the “Alarm” status message will be displayed.
Pressing the “Enter” key confirms the entry.

7.2.7.6

Max. measured temperature

After selecting this display, the largest measured temperature will be displayed. For comparison, the set
maximum limiting value will be displayed in the first line.

permissible +250 °C

measured +197 °C

This value cannot be reset since it stores the maximum measured process temperature.

«
...
73
74
75
76
77
...
»

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Отзывы:

Нет отзывов

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренд: OfiTE Страницы: 24

Mentor Visual iQ

Бренд: GE Страницы: 2

Бренд: Ralston Instruments Страницы: 52

Бренд: Olimpus Страницы: 12

Бренд: Bamo Страницы: 17

Бренд: Omega Страницы: 20

Бренд: LaMotte Страницы: 32

Бренд: Hammond Страницы: 36

Бренд: SIMET Страницы: 2

Бренд: Vega Страницы: 52

Бренд: Aalborg Страницы: 56

Бренд: Eddyfi Technologies Страницы: 72

WaveRunner 8000-R

Бренд: Teledyne Lecroy Страницы: 20

Proline Promag W 400

Бренд: Endress+Hauser Страницы: 64

Бренд: National Instruments Страницы: 40

Бренд: Hioki Страницы: 16

Бренд: National Instruments Страницы: 23

Бренд: LaMotte Страницы: 136

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды