Kobold Heinrichs Coriolis Mass Flow Meter Скачать руководство пользователя страница 86

Страница: 86 / 118

Heinrichs Messtechnik GmbH

Page 86 of 118

OPERATING MANUAL TMU-W / UMC4

7.2.10.6

Current output I2 assignment

This function allows the operator to define the measured value to be output as an analogue signal via current
output I2. Press “Enter” to display the current setting.

I2 assigned to

[Temperature]

The current assignment will be displayed and can be changed by toggling the arrow keys.
The operator can choose between the following settings:



Mass flow



Volume flow



Density



Temperature



not available (in this case the vendor setting must not be changed)

Pressing the “Enter” key confirms the entry.

Содержание Heinrichs Coriolis Mass Flow Meter























































































































Результаты поиска

Содержание Heinrichs Coriolis Mass Flow Meter

Отзывы:

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренды по названию

Популярные бренды

Kobold Heinrichs Coriolis Mass Flow Meter, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Heinrichs Coriolis Mass Flow Meter

Отзывы:

Похожие инструкции для Heinrichs Coriolis Mass Flow Meter

Бренды по названию

Популярные бренды