Kikusui PFX2532 Скачать руководство пользователя | Manualshive

Страница: 4 / 142

background image

4

PFX2532

•

I/F cable for PLZ-5W Electronic load

(

)

• Parallel cable for electronic loads (

PLZ-5W, PLZ-4W

)

For the safe use and safe maintenance of this product, the
following symbols are used throughout operation manual and
on the product. Note the meaning of each of the symbols to
ensure safe use of the product. (Not all symbols may be used.)

or

Indicates that a high voltage (over 1 000 V) is used here.
Touching the part causes a possibly fatal electric shock. If
physical contact is required by your work, start work only
after you make sure that no voltage is output here.

DANGER

Indicates an imminently hazardous situation which, if
ignored, will result in death or serious injury.

WARNING

Indicates a potentially hazardous situation which, if
ignored, could result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation which, if
ignored, may result in damage to the product and other
property.

Model

Description

Length

Quan
tity

SC05-PFX

I/F cable
For between a PFX2532 and PLZ-5W

Approx.
1 m

1 pc.

M8 screw set

2 sets

Model

Description

Length

Quan
tity

PC01-PLZ-4W

20-core flat cable
For between PLZ-4Ws and
between boosters

Approx.
30 cm

1 pc.

PC02-PLZ-4W

20-core flat cable
For between a PLZ-4W and
booster

Approx.
45 cm

1 pc.

PC01-PLZ-5W

1

1 One cable is included for the PLZ2405WB (booster).

Parallel operation signal cable
kit
For between PLZ-5Ws and
between a PLZ-5W and
booster

Approx.
30 cm

1 pc.

See

Ope

Indicates a prohibited act.

Indicates a warning, caution, or danger. When this
symbol is marked on the product, see the relevant
section in this manual.

Protective conductor terminal.

Chassis (frame) terminal.

On (power supply).

Off (power supply).

In position of a bi-stable push control.

Out position of a bi-stable push control.

Indicates that this product conforms to the
requirements of the Waste Electrical and Electronic
Equipment Directive.

In the EU, this product cannot be disposed of as
domestic household waste.

When disposing of this product, follow the Waste
Electrical and Electronic Equipment (WEEE)
Directive.

In areas outside of the EU, dispose of it as per the
instructions of the local authorities.

Safety Symbols

«
...
2
3
4
5
6
...
»

Содержание PFX2532















































































































































Отзывы:

Нет отзывов

Похожие инструкции для PFX2532

Бренд: Microchip Technology Страницы: 37

Бренд: C&K systems Страницы: 2

Бренд: Lawler Страницы: 2

Бренд: Waterway Страницы: 16

Бренд: Samson Страницы: 52

Бренд: VAT Страницы: 27

MorphoAccess SIGMA Extreme Series

Бренд: Idemia Страницы: 31

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: Parker Страницы: 12

Бренд: ZIMMERLI MESSTECHNIK Страницы: 12

Бренд: H-Tronic Страницы: 32

MicroTech II UV05

Бренд: AAF Страницы: 50

Бренд: Bentel Страницы: 88

Бренд: Zenith Страницы: 20

Бренд: Samson Страницы: 182

Бренд: PMFoundations Страницы: 5

Бренд: Weidmüller Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды