Kikusui PFX2532 Скачать руководство пользователя

Страница: 101 / 142

PFX2532

101

8Slot Unit (

ption) /

met

r Unit (

ption)

Connecting the Power Cord

The SL01-PFX conforms to IEC Overvoltage Category II (energy-consuming equipment that is
supplied from a fixed installation).

Turn the POWER switch off.

Check that the AC power line meets the nominal input rating of the SL01-PFX.

The SL01-PFX can receive a nominal line voltage in the range of 100 Vac to 240 Vac at
50 Hz or 60 Hz.

Connect the power cord to the AC INPUT inlet on the rear panel.

Use a power cord that conforms to the rated AC input voltage and current.

Connect the power cord plug to a properly grounded outlet.

WARNING

Risk of electric shock.

• The 8Slot Unit SL01-PFX conforms to IEC Safety Class I (equipment that has a protective

conductor terminal). Be sure to earth ground the product to prevent electric shock.

• The 8Slot Unit SL01-PFX is grounded through the power cord ground wire. Connect the

protective conductor terminal to earth ground.

• Use the included power cord to connect to the AC line. If the included cord cannot be used

because the rated voltage or the plug shape is incompatible, have a qualified engineer replace it
with an appropriate power cord that is 3 m or less in length. If obtaining a power cord is difficult,
contact your Kikusui agent or distributor.

• The power cord with a plug can be used to disconnect the SL01-PFX from the AC power line in an

emergency. Connect the plug to an easily accessible power outlet so that the plug can be
removed from the outlet at any time.

• Do not use the included power cord with other instruments.

Содержание PFX2532















































































































































Результаты поиска

Содержание PFX2532

Отзывы:

Похожие инструкции для PFX2532

Бренды по названию

Популярные бренды

Kikusui PFX2532, Руководство по эксплуатации

Результаты поиска

Содержание PFX2532

Отзывы:

Похожие инструкции для PFX2532

Бренды по названию

Популярные бренды