Keysight N4372E Скачать руководство пользователя страница 84

Страница: 84 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

User Interface Reference

If ‘Differential’ measurement is selected, three columns are shown. Here it

can be selected which ports to use on the differential side and which port

is connected to the LCA Optical Transmitter or Receiver.

Figure 18

Differential OE-measurement

The port configuration can only be changed when ‘User’ is selected in the

‘Mode’ listbox. If ‘Default’ is selected, the factory default port configuration

is used. ‘True Mode’ is only available in combination with ‘Differential’

measurements. If ‘True Mode’ is selected, a port configuration is shown

which allows true mode differential measurements on the network

analyzer. See network analyzer documentation for information about true

mode differential measurements.

For differential OE measurements, the network analyzer port to be used for

the user calibration measurement can be selected independently. If one of

the differential ports is selected, only a 3-port electrical calibration is

required. With the configuration shown above, a 4-port electrical

calibration would be required.

After pressing the ‘Apply’ button, the currently selected configuration is

written to the LCA server.

The ‘Apply’ button is only enabled when a valid configuration is selected.

Invalid configurations:
• Duplicate port assignment: The same NWA port is used as source and

transmitter port.

• Second differential port has the same or a lower port number than the

first differential port.

• The Receiver-port for the user calibration is the same as the port for the

LCA Optical Transmitter.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды