Keysight N4372E Скачать руководство пользователя страница 122

Страница: 122 / 152

122

Keysight N4372E Lightwave Component Analyzer User’s Guide

Maintenance

Heavy dirt

If the above procedure is not enough to clean your instrument, follow one

of the procedures below. Please consult

Cleaning

on page 114 for the

procedure relevant for this instrument.

If you are unsure of how sensitive your device is to cleaning, please contact

the manufacturer or your sales distributor.

How to clean connectors

Cleaning connectors is difficult as the core diameter of a single-mode fiber

is only about 9

m. This generally means you cannot see streaks or

scratches on the surface. To be certain of the condition of the surface of

your connector and to check it after cleaning, you need a microscope.

In the case of scratches, or of dust that has been burnt onto the surface of

the connector, you may have no option but to polish the connector. This

depends on the degree of dirtiness, or the depth of the scratches. This is a

difficult procedure and should only be performed by skilled personal, and

as a last resort as it wears out your connector.

To assess the projection of the emitted light beam you can use an infrared

sensor card. Hold the card approximately 5 cm from the output of the

connector. The invisible emitted light is project onto the card and becomes

visible as a small circular spot.

Preferred Procedure

Use the following procedure on most occasions.
1 Clean the connector by rubbing a new, dry cotton-swab over the

surface using a small circular movement.

2 Blow away any remaining lint with compressed air.

Procedure for Stubborn Dirt

Use this procedure particularly when there is greasy dirt on the connector:
1 Moisten a new cotton-swab with isopropyl alcohol.
2 Clean the connector by rubbing the cotton-swab over the surface

using a small circular movement.

WARNING

Never look into the end of an optical cable that is connected to an active

source.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды