Keysight N4372E Скачать руководство пользователя страница 134

Страница: 134 / 152

134

Keysight N4372E Lightwave Component Analyzer User’s Guide

Reinstalling and Updating the Software

Backing Up your LCA Data

The information for your particular configuration of the LCA and the factory

calibration data are kept in the “Table” and “Information” subdirectories of

the directory in which the software is installed.

These two directories are backed up under the "LCA" directory on the "D"

drive of your network analyzer. These directories are not overwritten when

performing the network analyzer's system recovery process.

Please refer to the user documentation of the network analyzer for

information on backing up calibration data.

Reinstalling the LCA Software

There are two cases:
• Updating the LCA software.
• Reinstalling the LCA software completely, for example after recovering

the network analyzer

Updating the LCA software

1 Before updating the software, you must remove the existing software.

In Windows’ Settings, go to the Control Panel and select Add or

Remove Programs.

Select the LCA application from the list of programs.

Remove the program.

2 Start the LCA setup software LCAInstaller.msi.
3 Follow the instructions on the screen. We recommend you use the

default settings.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды