Keysight N4372E Скачать руководство пользователя страница 80

Страница: 80 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

User Interface Reference

Default and Advanced Measurement Parameters

Use the default parameters for EO measurements of devices with a simple

stimulus and response path. This includes devices like sources, receivers

or amplifiers.

Use the advanced parameters for more comprehensive control of your

measurements.

Saving and Loading Setups

Saving setups

A setup contains the current state of the LCA user interface and optionally

also the current state of the network analyzer. Setups are stored as

XML-files or as compressed XML-files.

The settings on the “Tools” tab are not saved in the setup, since the

settings shown on this tab always reflect the current state of the LCA

hardware. After loading the setup the LCA system is configured to press

“Start” from the LCA user interface.

There are two ways of saving setups.

First saving method

Click

to save the current setup.

• If user calibration mode is set to “Measure” (only possible for OE and

OO measurements), you are asked to specify the electrical calibration

set to be saved with the setup.

This is the electrical calibration set to be used during user calibration

measurements.
Only a link to the electrical calibration set is saved, not the calibration

data itself.
For more details, see

Measuring Opto-Electrical (OE) devices

page 54 or

Measuring Optical-Optical (OO) Devices

on page 70.

• If User Calibration is set to “Load” (only possible for OE and OO

measurements), you will be asked to specify which user calibration file

should be loaded.

The filename of the calibration data is saved with the setup, not the

calibration data itself.
For more details, see

Measuring Opto-Electrical (OE) devices

page 54 or

Measuring Optical-Optical (OO) Devices

on page 70.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды