Keysight N4372E Скачать руководство пользователя страница 14

Страница: 14 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

Introduction

Line power connectors

In accordance with international safety standards, the instrument has a

three-wire power cable. When connected to an appropriate AC power

receptacle, this cable earths the instrument cabinet. The type of power

cable shipped with each instrument depends on the country of destination.

WARNING

To avoid the possibility of injury or death, you must observe the following

precautions before switching on the instrument.

•

Insert the power cable plug only into a socket outlet provided with a

protective earth contact. Do not use an extension cord without a

protective conductor. Using an extension cord without a protective

conductor means the instrument is not earthed.

•

Do not interrupt the protective earth connection intentionally.

•

Do not remove protective covers. Operating personnel must not

remove instrument covers. Component replacement and internal

adjustments must be made only by qualified service personnel.

•

Instruments that appear damaged or defective should be made

inoperative and secured against unintended operation until they can

be repaired by qualified service personnel.

•

Defective, damaged, or malfunctioning instruments must be returned

to a Keysight Technologies Service Center.

Do not operate the instrument in the presence of flammable gases or

fumes. Operation of any electrical instrument in such an environment

constitutes a definite safety hazard.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды