Keysight N4372E Скачать руководство пользователя страница 127

Страница: 127 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

127

Maintenance

Preferred procedure

Use the following procedure on most occasions.
1 Clean the interface by rubbing a new, dry cotton swab over the surface

using a small circular movement.

2 Blow away any remaining lint with compressed air.

Procedure for stubborn dirt

Use this procedure when there is greasy dirt on the interface.
1 Moisten a new cotton swab with isopropyl alcohol.
2 Clean the interface by rubbing the cotton swab over the surface using

a small circular movement.

3 Take a new, dry soft tissue and remove the alcohol, dissolved sediment

and dust, by rubbing gently over the surface using a small circular

movement.

4 Blow away any remaining lint with compressed air.

How to clean instruments with a recessed lens interface

For instruments with a deeply recessed lens interface (for example the

Keysight Technologies 81633A and 81634A Power Sensors) do not follow

this procedure. Alcohol and compressed air could damage your lens even

further.

Keep your dust and shutter caps on when your instrument is not in use.

This should prevent it from getting too dirty.

If you must clean such instruments, please refer the instrument to the

skilled personnel of the Keysight service team.

Preferred procedure

Use the following procedure on most occasions.
1 Blow away any dust or dirt with compressed air.

If this is not sufficient, then do the following:

Clean the interface by rubbing a new, dry cotton swab over the

surface using a small circular movement.

Blow away any remaining lint with compressed air.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды