Keysight N4372E Скачать руководство пользователя страница 138

Страница: 138 / 152

138

Keysight N4372E Lightwave Component Analyzer User’s Guide

Definition of Terms

Absolute frequency response uncertainty

The maximum difference between measured Responsivity of a device

under test and the actual (true) responsivity, expressed in dBe.

Conditions

: as specified.

Measurement

: Based on a reference RF O/E receiver.

Average output power (optical)

The (actual or nominal) average output power from the LCA optical output.

Average output power range (optical)

The nominal (selectable) range for Average output power (optical).

Average output power stability (optical)

The variation of the optical Average output power (optical) P over time,

calculated as

where maxt{} and mint{} are the maximum and minimum value over time t.

Conditions

: Time period as specified after modulator auto bias (“modulator

optimization”) is performed with the selected wavelength. Other conditions

as specified.

Measurement

: Using an average power meter with averaging time set to 1

Average output power uncertainty (optical)

The maximum difference between actual (true) Average output power

(optical) and the nominal (selected) average output power.

Conditions

: After modulator auto bias (“modulator optimization”)

performed with the selected wavelength. Other conditions as specified.

NOTE

Any change in the cabling after calibration add to the specified absolute

frequency response uncertainty.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды