Keysight N4372E Скачать руководство пользователя страница 37

Страница: 37 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

Setting Up the Instrument

11 Connect the optical patch cord to the optical input of the LCA Optical

Receiver.

12 Remove the dust caps from the PMF optical patch cord

(N4372-87905).

13 Connect the optical patch cord to the laser output of the LCA Test Set

controller and the laser input of the LCA Optical Transmitter.

14 Remove the dust caps from the PMF optical patch cord.
15 Connect the optical patch cord to the optical output of the LCA Optical

Transmitter.

16 On the rear, connect the network analyzer to the LCA Test Set

Controller using the supplied USB cable.

17 Connect the power cables.
18 Continue with

Performance Quick Check

on page 39 or

Starting the

Lightwave Component Analyzer

on page 50.

CAUTION

Always use optical patch cords to connect to your DUT. This protects the

connectors of the LCA Optical Receiver/Transmitter, by minimizing the

number of connector changes.

CAUTION

Make sure to connect only matching connector types to the LCA Optical

Receiver/Transmitter: connecting a straight connector to an angled port,

or vice versa, will damage both interfaces.

CAUTION

Before you connect any fiber-optic cable to the Lightwave Component

Analyzer, please ensure it has been properly cleaned.
Fiber-optic connectors are easily damaged when connected to dirty or

damaged cables and accessories. Improper cleaning or handling may

lead to expensive instrument repairs, damaged cables, or compromised

measurements.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды