Keysight N4372E Скачать руководство пользователя страница 11

Страница: 11 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

Introduction

Instrument markings

Instrument Marking

Description

The instruction manual symbol. The product is marked with this warning symbol when it is necessary for the user to refer
to the instructions in the manual.

The laser radiation symbol. This warning symbol is marked on products which have a laser output.

The Off-On symbols are used to mark the positions of the instrument power operating switch.

The recycling symbol indicates the general ease with which the instrument can be recycled.

The C-Tick mark is the certification mark of the Australian Communications Authority.

The CE mark is the conformity marking of the European Community.

The CSA mark is the certification mark of the Canadian Standards Association.

WARNING

If this product is not used as specified, the protection provided by the

equipment could be impaired. This product must be used in a normal

condition (in which all means for protection are intact) only.

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды