Keysight N4372E Скачать руководство пользователя страница 36

Страница: 36 / 152

Keysight N4372E Lightwave Component Analyzer User’s Guide

Setting Up the Instrument

Don’t apply any DC or RF signal to the RF output of the LCA Optical

Receiver. This might irreversibly damage the LCA Optical Receiver.
Don’t apply any DC signal to the RF input of the LCA Optical

Transmitter. This might irreversibly damage the LCA Optical

Transmitter.

9 Remove the dust cap from the optical output.
10 Remove the dust caps from the SMF optical patch cord (Option 021:

N4373-87907, Option 022: N4373-87906).

CAUTION

Always rotate the nut and never the female to female adapter.
Rotating the adapter can damage the electrical interface of the adapter

and the connector on the LCA Optical Receiver/Transmitter.
Avoid mechanical stress on the 1.0mm RF connection. Ensure that the RF

connectors of the electrical frequency extender head and the LCA Optical

Receiver/Transmitter are at the same height and longitudinally aligned

when tightening the adapter.
If the height of the LCA Optical Receiver/Transmitter and the frequency

extender head does not align, connecting the two will lead to stress on

the 1.0mm RF connection. Adjust the height of the lower part by

unscrewing the rubber feet until the height matches.
The LCA Optical Transmitter/Receiver must not be inverted during

assembly or operation

Figure 4

LCA Optical Receiver and Test Set Controller connected to a Network

Analyzer

Содержание N4372E

























































































































































Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды

Keysight N4372E, Руководство пользователя

Результаты поиска

Содержание N4372E

Отзывы:

Бренды по названию

Популярные бренды