manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 99

 N5511A Phase Noise Test System User’s Guide                                                                                               99

Absolute Measurement Examples
Input Ports

Input Ports

The N5511A Phase Noise Tests System phase detector frequency specification 

are the following.

For optimal performance, however, when performing a measurement, N5510 

software defaults to detector selections that do not match the hardware 

capabilities. When performing a measurement, the software default detector 

selections use the following guidelines:

This can be overwritten by manually selecting the detector to be utilized in the 

measurement setup, as long as the input signal is within the hardware 

specifications of the detector input. 

Low Frequency Inputs

 

(SMA)

 

All Options

High Frequency Inputs

 

(Type K)

 

Option 526

High Frequency Inputs

 

(Type K)

 

Option 540

AM Noise Input

 

(SMA)

 

All Options

Carrier frequency 

range

50 kHz to 3 GHz

1.2 GHz to 26.5 GHz

1.2 GHz to 40 GHz

50 kHz to 40 GHz 

RF input power

 

LO input power

0 dBm to +23 dBm

 

+15 dBm to +23 dBm

0 dBm to +15 dBm

 

+7 dBm to +15 dBm 

0 dBm to +15 dBm

 

+7 dBm to +15 dBm 

0 dBm to +30 dBm

 

N/A

Low Frequency Inputs

50 kHz to 1.6 GHz

High Frequency Inputs

1.6 GHz and above

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды