manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 52

 52                                                                                               N5511A Phase Noise Test System User’s Guide

Expanding Your Measurement Experience
GUI Features

Measurement Preferences

Figure 4-15 

Measurement Preferences

Pause At Connection Diagram:

 check to skip Connection Diagram when a New 

Measurement is initiated.

Don't Automatically Clear Graph:

 when restarting a measurement, the default 

behavior is for the current trace to be cleared. To retain the trace, uncheck this 

option.

Don't Automatically change Previous Graph Color:

 when retaining a trace, the 

application defaults the previous trace to a different color to not conflict with 

the new trace. To keep the previous trace color, uncheck this option.

Don't Mark Spur:

 spurs will not be marked as spurs.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды