manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 75

 N5511A Phase Noise Test System User’s Guide                                                                                                75

Absolute Measurement Fundamentals
Changing the PTR

The Tuning Qualifications 

Changing the PTR is accomplished by changing the tune range of VCO value or 

the VCO tuning constant value or both. There are several ways this can be 

done. However, when considering these or any other options for changing the 

PTR, it is important to remember that the VCO source must always meet the 

following tuning qualifications.

— The tuning response of the VCO source must always remain monotonic. 
— The VCO source’s output level must remain constant across its tuning 

range. 

As long as these qualifications are met, and the software does not indicate any 

difficulty in establishing its calibration criteria, an increase in PTR will not 

degrade the system’s measurement accuracy. 
The following methods may be considered for increasing or decreasing the 

PTR. 

Voltage controlled oscillators

1.

Select a different VCO source that has the tuning capabilities needed for 

the measurement. 

2.

Increase the tune range of the VCO source. 

Be careful not to exceed the input voltage limitations of the Tune Port on the VCO source.

Increasing the tune range of the VCO is only valid as long as the VCO source is able to 

continuously meet the previously mentioned tuning qualifications. 

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды