manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 268

 268                                                                                               N5511A Phase Noise Test System User’s Guide

AM Noise Measurement Fundamentals
Calibration and Measurement General Guidelines

Figure 11-12 

Dual Channel AM noise measurement setup using single-sided spur

2.

Measure the power which will be applied to the AM detector. It must be 

between 0 and +23 dBm. 

3.

Measure the carrier-to-single-sided-spur ratio and the spur offset at the 

input to the AM detector with an RF spectrum analyzer. See 

Figure 11-13

. 

The spur should be adjusted such that it is between –30 and –60 dBc, with 

a carrier offset of 10 Hz to 20 MHz.

Figure 11-13 

Measuring relative spur level

4.

Enter the relative power level and offset of the tone into the measurement 

definition in the software. The AM detector will remove the PM 

component, thus the end result in the measurement will be a spur that is 6 

dB lower than what the analyzer measured. See 

Figure 11-14

. 

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды