Keysight Technologies N5511A Скачать руководство пользователя страница 257

Страница: 257 / 369

N5511A Phase Noise Test System User’s Guide 257

AM Noise Measurement Fundamentals
Amplitude Noise Measurement

Amplitude Noise Measurement

The level of amplitude modulation sidebands is also constant with increasing

modulation frequency. The AM detector gain can thus be measured at a single

offset frequency and the same constant will apply at all offset frequencies.

Replacing the phase detector with an AM detector, the AM noise measurement

can be calibrated in the same way as PM noise measurement, except the phase

modulation must be replaced with amplitude modulation.
The AM noise measurement is a characterization of a source. The residual AM

noise of a DUT can only be made by using a source with lower AM noise, then

subtracting that AM noise from the measured output noise of the DUT. The

noise floor of this technique is the noise floor of the source.

AM noise measurement block diagrams

Figure 11-1

Single Channel AM Measurement

Figure 11-2

Dual Channel AM Measurement

Содержание N5511A


















































































































































































































































































































































































Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды

Keysight Technologies N5511A, Руководство пользователя

Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды