manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 86

 86                                                                                               N5511A Phase Noise Test System User’s Guide

Absolute Measurement Fundamentals
Calibration

Calibration

Overview

User calibrations are used to establish a reference constant for relative 

measurements made on the system. For absolute measurements, the 

amplitude of the carrier needs to be determined before the measurement since 

the carrier is removed from the measurement when quadrature is established. 

In absolute measurements various parameter of the reference need to be 

measured. The type of calibration to be used is determined by the system 

configuration and equipment availability. User calibrations need to be run 

every time there is a change to the system or DUT parameters.
For absolute measurements, the N5511A supports four different options for 

calibration, see 

Figure 5-23

:

— Use current phase detector constant
— Derive detector constant from measured beat note
— Derive detector constant from single-sided spur
— Derive detector constant from double-sided spur

Figure 5-23 

Phase Detector Calibration Options

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды