Keysight Technologies N5511A Скачать руководство пользователя страница 74

Страница: 74 / 369

74 N5511A Phase Noise Test System User’s Guide

Absolute Measurement Fundamentals
Changing the PTR

Changing the PTR

The peak tuning range (PTR) for the phase lock loop measurement is set by the

tune range entered for the VCO and the VCO’s tuning constant. (If the

calibration technique is set to measure the VCO tuning constant, the measured

value is used to determine the system’s PTR.)

PTR= VCO Tuning Constant X Voltage Tuning Range

From the PTR, the phase noise software derives the capture and drift tracking

Ranges for the measurement. These ranges set the frequency stability

requirements for the sources being used.
The PTR also determines the phase lock loop (PLL) bandwidth for the

measurement. An important attribute of the PLL bandwidth is that it

suppresses the close-in noise which would otherwise prevent the system from

locking the loop.

Figure 5-14

Peak tuning range

Содержание N5511A


















































































































































































































































































































































































Результаты поиска

Содержание N5511A

Отзывы:

Бренды по названию

Популярные бренды

Keysight Technologies N5511A, Руководство пользователя

Результаты поиска

Содержание N5511A

Отзывы:

Бренды по названию

Популярные бренды