manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 181

 N5511A Phase Noise Test System User’s Guide                                                                                               181

Residual and Additive Noise Measurement Fundamentals
Calibrating the Measurement

The DC peak voltage method is a very convenient calibration for residual 

measurements as a cal source is not needed. The user adjusts the phase shift 

until a peak positive voltage is measured and then adjusted again to measure a 

minimum negative voltage. The meters on the application are used to identify 

these peaks. 

Figure 7-11

 shows how the meters operate as well as a 

mathematical representation of ± DC peak voltage cal. Measuring the peak 

positive voltage means adjusting the phase shifter(s) so that the LO path of 

each channel is in phase with the RF path into the mixer. To measure the 

minimum negative voltage, the phase shifter(s) are adjusted so that the LO 

path into the phase detector is 180 degrees out of phase relative to the RF 

input.

Figure 7-11 

± DC Peak Voltage

This method has moderate accuracy since it is measuring the signal in the IF 

after the mixer, at which point the signal present may not be a perfect sinusoid. 

This causes the peak value measured to be inaccurate which can affect the 

Kphi by as much as 2 dB. In many cases this may not be an issue.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды