manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 73

 N5511A Phase Noise Test System User’s Guide                                                                                                73

Absolute Measurement Fundamentals
Tracking Frequency Drift

Evaluating beat note drift 

The Checking the beat note section included in each phase lock loop 

measurement example in this chapter provides a procedure for adjusting the 

beat note to within the Capture Range set for the measurement. If you have not 

done so already, verify that the beat note signal can be tuned to within the 

Capture Range and that it will remain within the range. 
Continue to observe the beat note and verify that it will not drift beyond the 

drift tracking range (24% of the PTR) during the measurement period. The 

length of the measurement period is primarily a function of the frequency offset 

range specified for the measurement (Start to Stop Frequency).

Action 

If beat note drift exceeds the limits of the Capture or drift tracking ranges set 

for your measurement, the system is not able to complete the measurement. 

You have two possible alternatives. 

1.

Minimize beat note drift. 

—

By Allowing sources to warm-up sufficiently. 

—

By Selecting a different reference source with less drift. 

2.

Increase the capture and drift tracking Ranges. 

—

By Selecting a measurement example in this chapter that specifies a 

drift rate compatible with the beat note drift rate you have observed.

—

By Increasing the peak tuning range for the measurement. (Further 

information about increasing the PTR is provided in Changing the 

PTR.) 

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды