manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 115

 N5511A Phase Noise Test System User’s Guide                                                                                               115

Absolute Measurement Examples
Single Channel Measurement

peak tuning range for your VCO can be estimated by multiplying the VCO 

tuning constant by the tune range of VCO. Refer to 

Chapter 14, “Evaluating 

Your Measurement Results”

 if you are not familiar with the relationship 

between the PLL capture range and the peak tuning range of the VCO. The 

beat note frequency is set by the relative frequency difference between the two 

sources. If you have two very accurate sources set at the same frequency, the 

resulting beat note will be very close to 0 Hz. Searching for the beat note will 

require that you adjust the center frequency of one of the sources above and 

below the frequency of the other source until the beat note appears on the 

oscilloscope's display. If incrementing the frequency of one of the sources does 

not produce a beat note, you will need to verify the presence of an output 

signal from each source before proceeding.

Figure 6-9 

Pause point window for when a beat note needs to be tuned

Figure 6-10 

Monitor output displaying adjusted beat note within specified range

If the center frequencies of the sources are not close enough to create a beat note within the 

capture range, the system will not be able to complete its measurement.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды