manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 240

 240                                                                                              N5511A Phase Noise Test System User’s Guide

FM Discriminator Measurement Examples
FM Discriminator Single Channel Measurement using FM Rate and Deviation 

Calibration

FM Discriminator Single Channel Measurement using FM Rate and 

Deviation Calibration

Required Equipment

Table 10-3

 shows equipment required for this example in addition to the phase 

noise test system and your DUT. 

Determining the discriminator (delay line) length

Perform the following steps to determine the minimum delay line length (

τ

) 

possible to provide an adequate noise to measure the source.

1.

Determine the delay necessary to provide a discriminator noise floor that 

is below the expected noise level of the DUT. 

Figure 10-11

 shows the noise 

floor of the discriminator for given delay times (t).

2.

Determine the length of coax required to provide the necessary delay (

τ

). 

(Eight feet of BNC cable will provide 12 ns of delay for this example.)

3.

Determine the loss in the delay line. Verify that the signal source will be 

able to provide a power level at the output of the delay line of b5 

and +17 ICBM. Be sure to take into account an additional 4 to 6 dB of loss 

To prevent damage to the test set’s components, 

do not

 apply a signal beyond the systems 

specifications. Refer to the data sheet for power specifications. 

In order to use the FM rate and deviation calibration method you must have a signal source that is 

calibrated for FM modulation rate and FM deviation parameters. All Keysight Technologies signal 

generators meet this requirement.

To ensure accurate measurements allow the DUT and measurement equipment to warm up at 

least 30 minutes before making the noise measurement. 

Table 10-3 

Required Equipment for the FM Discriminator 

Measurement Example

Equipment

Quantity

Comments

Signal Generator

1

+19 dBm output level at tested carrier frequency.

Calibrated FM at a 20 kHz rate with 10 kHz Peak 

Deviation.

Power Splitter

1

NARDA 30183

Delay Line

Delay (or length) adequate to decorrelate source noise.

Phase Shifter

1

±180° phase shifter at lowest carrier frequency tested.

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды