Keysight Technologies N5511A Скачать руководство пользователя страница 312

Страница: 312 / 369

312 N5511A Phase Noise Test System User’s Guide

Advanced Software Features
Phase-Lock-Loop Suppression

Ignore-Out-Of-Lock Mode

Figure 15-2

Ignore out-of-lock conditions

The Ignore Out Of Lock test mode enables all of the troubleshooting mode

functions, plus it causes the software to not check for an out-of-lock condition

before or during a measurement. This allows you to measure sources with high

close-in noise that normally would cause an out-of-lock condition and stop the

measurement. When Ignore Out Of Lock is selected, the user is responsible for

monitoring phase lock. This can be accomplished using an oscilloscope

connected to the test set Aux. Monitor port to verify the absence of a beat note

and monitor the DC output level.

— When Ignore Out Of Lock is selected, the test system does not verify the

phase lock of the measurement. The user must ensure that the

measurement maintains phase lock during the measurement.

Содержание N5511A


















































































































































































































































































































































































Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды

Keysight Technologies N5511A, Руководство пользователя

Результаты поиска

Содержание N5511A

Отзывы:

Похожие инструкции для N5511A

Бренды по названию

Популярные бренды