manualshive.com logo in svg

Keysight Technologies N5511A, Руководство пользователя

Поделиться
Скачать
Keysight Technologies N5511A Скачать руководство пользователя страница 131

 N5511A Phase Noise Test System User’s Guide                                                                                               131

Absolute Measurement Examples
Dual Channel (EFC)

New Measurement

Close Define Window. From the File Menu: 

Measure

, 

New Measurement

. 

If the beat note is not within the frequency range required, the software will 

prompt to tune the reference.

Checking the Beat Note

Use an oscilloscope (connected to the Monitor port on the test set) or a 

counter to check the beat note being created between the reference source 

and your DUT.

Figure 6-18 

Oscilloscope displaying monitor output of phase detector

The objective of checking the beat note is to ensure that the center frequencies 

of the two sources are close enough in frequency to create a beat note that is 

within the capture range of the system. The phase lock loop (PLL) capture 

range is 5% of the peak tuning range of the VCO source you are using. (The 

peak tuning range for your VCO can be estimated by multiplying the VCO 

tuning constant by the tune range of VCO. Refer to 

Chapter 14, “Evaluating 

Your Measurement Results”

 if you are not familiar with the relationship 

between the PLL capture range and the peak tuning range of the VCO. The 

beat note frequency is set by the relative frequency difference between the two 

sources. If you have two very accurate sources set at the same frequency, the 

resulting beat note will be very close to 0 Hz. Searching for the beat note will 

require that you adjust the center frequency of one of the sources above and 

below the frequency of the other source until the beat note appears on the 

Содержание N5511A


















































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды