manualshive.com logo in svg

Keithley 6517A, Руководство пользователя

Инструкция пользователя для Keithley 6517A доступна для загрузки бесплатно на нашем сайте. Изучите всю функциональность этого прибора, скачав руководство пользователя прямо сейчас. manualshive.com - ваш надежный источник качественных руководств для ваших устройств.

Поделиться
Скачать
background image

Front Panel Operation

2-75

Idle 

The instrument is considered to be in the idle state whenever
it is not operating within one of the three layers of the trigger
model. The front panel ARM indicator is off when the instru-
ment is in the idle state. While in the idle state, the instrument
cannot perform any measurement or scanning functions. 

From the front panel there are three ways to put the instru-
ment into idle: 

• Select RESET GPIB from the SAVESETUP option of

the main menu. Press the TRIG key to take a reading.
After each reading, the instrument returns to the idle
state. 

• Select HALT from the ADVANCED item of CONFIG-

URE TRIGGER menu. Press the TRIG key to resume
triggering. The INIT (ON) option of the ADVANCED
trigger menu structure will also take the instrument out
of idle. 

• Press the OPTION CARD key to place the Model

6517A in the scan mode. Triggering will resume when
the scan is started or if the scan is aborted by pressing
EXIT. 

Trigger Model Layers 

As can be seen in Figure 2-57, the trigger model uses three
layers: the Arm Layer, Scan Layer and Measure Layer. For
IEEE-488 bus operation, these layers are known as Arm Lay-
er 1, Arm Layer 2 and the Trigger Layer. 

Once the Model 6517A is taken out of the idle state, opera-
tion proceeds through the layers of the trigger model down
to the device action where a measurement occurs. 

Control Sources —

 In general, each layer contains a control

source which holds up operation until the programmed event
occurs. The control sources are described as follows: 

• Immediate — With this control source selected, event

detection is immediately satisfied allowing operation to
continue. 

• Manual — Event detection is satisfied by pressing the

TRIG key. Note that the Model 6517A must be taken
out of remote before it will respond to the TRIG key.
Pressing LOCAL takes the instrument out of remote. 

• GPIB — Event detection is satisfied when a bus trigger

(GET or *TRG) is received by the Model 6517A. 

• RT-Clock — Event detection in the Arm Layer is satis-

fied when the programmed time and date occurs. The
real-time clock control source is not available in the
Scan Layer and Measure Layer. 

• Timer — Event detection is immediately satisfied on

the initial pass through the layer. Each subsequent de-
tection is satisfied when the programmed timer interval
(1 to 999999.999 seconds) elapses. A timer resets to its
initial state when operation loops back to a higher layer
(or idle). Note that a timer is not available in the Arm
Layer. 

• External — Event detection is satisfied when an input

trigger via the EXTERNAL TRIGGER connector is re-
ceived by the Model 6517A. 

• Triglink — Event detection is satisfied when an input

trigger via the TRIGGER LINK is received by the Mod-
el 6517A. 

• Hold — With this selection, event detection is not satis-

fied by any of the above control source events and oper-
ation is held up. 

Source Bypasses —

 As can be seen in the flowchart, each

layer has a path that allows operation to loop around the con-
trol source. Each path is called a source bypass. 

When a source bypass is enabled, and the external or trigger
link (triglink) control source is selected, operation loops
around the control source on the initial pass through the lay-
er. If programmed for another event detection in the layer,
the bypass loop will not be in effect though it is still enabled.
The bypass loop resets (be in effect) if operation loops back
to a higher layer (or idle). 

In the Arm Layer and Scan Layer, enabling a source bypass
also enables the respective output trigger. In the Trigger Lay-
er, its output trigger is always enabled and occurs after every
device action. See Output Triggers for more information. 

Delays —

 The Scan Layer and the Measure Layer have a

programmable delay (0 to 999999.999 seconds) that is en-
forced after an event detection. 

Device Action —

 The primary device action is a measure-

ment. However, the device action could include a function
change and a channel scan (if scanner is enabled). A channel
is scanned (closed) before a measurement is made. When
scanning internal channels, the previous channel opens and
the next channel closes (break-before-make). Also included
in the device action is the internal settling time delay for the
relay. 

Output Triggers —

 In the Arm Layer and Scan Layer the

output triggers are enabled only if their respective source by-
passes are also enabled. If a trigger link (triglink) control
source is selected, the output trigger pulse is available on the
selected TRIGGER LINK output line. For all other control

Содержание 6517A
























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517A

Medeli SP40A User Manual preview
SP40A
Бренд: Medeli Страницы: 14
Callaway 200 S Manual preview
200 S
Бренд: Callaway Страницы: 11
Felix Instruments F-940 Operation Manual preview
F-940
Бренд: Felix Instruments Страницы: 102
Keithley SourceMeter 2400 User Manual preview
SourceMeter 2400
Бренд: Keithley Страницы: 594
Keithley System SourceMeter 2601B Reference Manual preview
System SourceMeter 2601B
Бренд: Keithley Страницы: 864
Labgear S201 User Manual preview
S201
Бренд: Labgear Страницы: 8
Keithley SourceMeter 2600B Series Reference Manual preview
SourceMeter 2600B Series
Бренд: Keithley Страницы: 897
National Instruments NI 9219 Getting Started Manual preview
NI 9219
Бренд: National Instruments Страницы: 38
SIGLENT CP4000 Series Instructions Manual preview
CP4000 Series
Бренд: SIGLENT Страницы: 32
HBM T10F Mounting Instructions preview
T10F
Бренд: HBM Страницы: 84
Kawai KSP 10 Owner'S Manual preview
KSP 10
Бренд: Kawai Страницы: 72
Kreg Precision KMS7101 Instructional Manual preview
Precision KMS7101
Бренд: Kreg Страницы: 16
Sensitech FreezeAlert Instructions For Use preview
FreezeAlert
Бренд: Sensitech Страницы: 2
Baker Hughes Panametrics XDP User Manual preview
Panametrics XDP
Бренд: Baker Hughes Страницы: 64
IROX PE-DRO Operating Instructions Manual preview
PE-DRO
Бренд: IROX Страницы: 8
SEAWARD Electronic Rigel 266 Plus Instruction Manual preview
Rigel 266 Plus
Бренд: SEAWARD Electronic Страницы: 57
Charder HM201M User Manual preview
HM201M
Бренд: Charder Страницы: 12
GW Instek LCR-800 Series User Manual preview
LCR-800 Series
Бренд: GW Instek Страницы: 91

Бренды по названию

Популярные бренды

Загрузить еще бренды