manualshive.com logo in svg

Keithley 6517A, Руководство пользователя

Инструкция пользователя для Keithley 6517A доступна для загрузки бесплатно на нашем сайте. Изучите всю функциональность этого прибора, скачав руководство пользователя прямо сейчас. manualshive.com - ваш надежный источник качественных руководств для ваших устройств.

Поделиться
Скачать
background image

Front Panel Operation

2-125

GENERAL MENU selection is used to set the time date and
format (12-hour or 24-hour) for the real time clock. 

TIME: This item is used to set the time for the clock. If the
12-hour format is selected, “AM” or “PM” will be displayed.
The absence of “AM” or “PM” denotes the 24-hour format.
The format for time can be changed with the FORMAT menu
item. Use the cursor keys and the range keys to set the time
(hours:minutes:seconds). Press AUTO to set seconds to zero. 

DATE: This item is used to set the date for the clock. Use the
cursor keys and the range keys to set the date. Note that the
day of the week (Sun, Mon, etc.) is automatically calculated
and displayed for the date. 

FORMAT: This item is used to select the time format for the
clock: 

• 12-HOUR — With this selection, real-time timestamps

for buffer readings are provided in the 12-hour format
(AM or PM). Also, the real-time clock control source
for the Arm Layer must be set using the 12-hour format. 

• 24-HOUR — With this selection, real-time timestamps

for buffer readings are provided in the 24-hour format.
Also, the real-time clock control source for the Arm
Layer must be set using the 24-hour format. 

Note that real-time timestamps for bus readings are always
provided in the 24-hour format, regardless of the FORMAT
selection. 

2.20 Scanning 

The Model 6517A can be used with an internal scanner card
(i.e., Model 6521 or 6522) or with external scanner cards in-
stalled in switching mainframes such as the Models 706,
7001 and 7002. 

A scanner allows you to switch among a number of input sig-
nals to the Model 6517A for measurement. The channel con-
trol and scanning capabilities depend on whether an internal
or external scanner card is being used, as well as on the ca-
pabilities of the scanner card in question. 

2.20.1 Internal scanning 

By installing one of the optional scanner cards in the rear
panel option slot, the Model 6517A can close and open indi-
vidual channels, or scan through the channels. 

Detailed operating instructions for internal scanning are pro-
vided in the instruction manual for that particular scanner

card. For example, to use the Model 6521 scanner card, refer
to the Model 6521/6522 Instruction Manual for operating in-
formation. 

2.20.2 External scanning 

When using external scanning, you can configure the Model
6517A to measure up to 400 channels. In order to synchro-
nize Model 6517A measurements with external channel clo-
sure, connect the Model 6517A external trigger inputs or the
trigger link to the external switching mainframe trigger in-
puts and outputs. Refer to paragraphs 2.15.4 and 2.15.5 for
examples on using external triggering and the trigger link. 

Use the following information to configure the Model 6517A
for external scanning, and to start the external scan. Refer to
the documentation supplied with the switching mainframe
and the scanner card for specific configuration and connec-
tion information.

The following procedure uses menu structures to configure
the instrument for external scanning. General rules to navi-
gate through the menus are provided in paragraph 2.3.5.

1. Set up the Model 6517A for the desired measurement

(i.e., set function, range, etc.).

NOTE

If there is no card installed in the option
slot of the Model 6517A, external scan-
ning will automatically be selected. If
there is a card installed in the option slot,
you will have to select external scanning
as explained in the following step:

2. Press CONFIG and then CARD, and perform step a or b.

A. Option slot empty — You will be prompted to spec-

ify the number of external channels (inputs) to scan.
After entering the value, press ENTER.

B. Card installed in option slot — Select the ENTER-

NAL-INPUTS (CHANNELS) option from the
menu and then specify the number of external chan-
nels (inputs) to scan. After entering the value, press
ENTER. Use the EXIT key to back out of the menu
structure.

3. Press the CARD key and perform step a or b.

A. Option slot empty — The displayed message will

prompt you to reset the external scanner. Press EN-
TER when ready.

Содержание 6517A
























































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 6517A

Saimo 6101 Operating And Service Manual preview
6101
Бренд: Saimo Страницы: 101
Sage SIP Operation And Instruction Manual preview
SIP
Бренд: Sage Страницы: 68
YOSensi YO H2O User Manual preview
YO H2O
Бренд: YOSensi Страницы: 26
YOSensi YO Pulse User Manual preview
YO Pulse
Бренд: YOSensi Страницы: 26
Kawai MP9500 Owner'S Manual preview
MP9500
Бренд: Kawai Страницы: 64
Kawai MR170 Owner'S Manual preview
MR170
Бренд: Kawai Страницы: 28
Kawai MR370 Owner'S Manual preview
MR370
Бренд: Kawai Страницы: 28
janitza UMG 96RM-P Operating Instructions And Technical Data preview
UMG 96RM-P
Бренд: janitza Страницы: 128
Autometers Systems A-400 Series Programming And Installation Brochure preview
A-400 Series
Бренд: Autometers Systems Страницы: 16
Fluidwell F011-A Manual preview
F011-A
Бренд: Fluidwell Страницы: 48
IDEAL 61-737 Operation And Safety Manual preview
61-737
Бренд: IDEAL Страницы: 84
turck FTCI-3/4D15A4P-2LUX-H1141 Quick Start Manual preview
FTCI-3/4D15A4P-2LUX-H1141
Бренд: turck Страницы: 2
Magneti Marelli Smart Gas Operating Manual preview
Smart Gas
Бренд: Magneti Marelli Страницы: 20
TDE Instruments Digalox DPM72-MPPA Instruction Manual preview
Digalox DPM72-MPPA
Бренд: TDE Instruments Страницы: 8
Young 03102L Instruction Manual preview
03102L
Бренд: Young Страницы: 7
Automation Direct ProSense LPM1 Series Operating Instructions Manual preview
ProSense LPM1 Series
Бренд: Automation Direct Страницы: 29
Seli STS-15 Manual preview
STS-15
Бренд: Seli Страницы: 68
Analog Devices AD5934 Manual preview
AD5934
Бренд: Analog Devices Страницы: 40

Бренды по названию

Популярные бренды

Загрузить еще бренды