ITT Goulds Pumps 3175 Скачать руководство пользователя страница 67

Страница: 67 / 87

Figure 65: Bearing frame to bearing adapter

15. To install shaft sleeve and stuffing box cover:

a) On units with a packed stuffing box, slide shaft sleeve with O-ring in place on the shaft. Tap

stuffing box bushing into place by using a sleeve. Check sleeve O.D. and bushing I.D. so it
meets requirements of

. Lift stuffing box cover into po-

sition at impeller end of shaft. Guide stuffing box cover over shaft and sleeve to prevent contact
to these surfaces. Bolt the stuffing box cover to the frame adapter.

b) On units with a mechanical seal, refer to the order acknowledgement and seal drawing (sup-

plied with the pump) to determine seal type and mounting dimensions.

16. The following instructions refer to pumps equipped with mechanical seals.

a) Before mounting any seals, wipe the seal faces carefully with a clean, soft doth and oil lightly

with clean oil.

b) Assemble gland, stationary seat, gland and seat gaskets. Carefully slide assembly on sleeve.

Lightly oil the rotary portion of the seal and slide on sleeve. Position rotary at proper distance
from end of sleeve. Correct dimension is shown on the seal drawing. See

6.8 Set the Mechani-

cal Seals on page 67

for methods of positioning the rotary.

d) Slide the stuffing box cover over shaft. Bolt the stuffing box cover to the frame adapter.

NOTICE:

Be careful not to damage seal on units with double seals. Make sure inboard stationary seat is
properly positioned.

17. Place stuffing box cover-to-casing gasket against shoulder of stuffing box cover. Small amounts of

O-ring lube may be used on both sides of gasket to seal and secure gasket in place.

6.7 Reassemble the Pump

3175 Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3175
























































































Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3175, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды