ITT Goulds Pumps 3175 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 87

background image

•

Electrical connections must be made by certified electricians in compliance with all
international, national, state, and local rules.

•

Refer to driver/coupling manufacturer's installation and operation manuals (IOM) for
specific instructions and recommendations.

NOTICE:

Make sure to lubricate the packing. Failure to do so may result in shortening the life of the
packing and the pump.

Before packing the stuffing box, make sure box is dean and contains no foreign material. If unit has a
metal lantern ring, assembled with the pump, make sure ring is outside the stuffing box.

Stuffing box packing is furnished in the box of fittings which accompanies the pump. When packing the
stuffing box, refer to the

8.3 Parts List on page 74

for the arrangement of packing rings and lantern ring.

Depending upon the particular pump and/or application, the lantern ring may be in the middle or bottom
of the stuffing box, incorporated in another part or not used at all.

Some packing rings are die-formed and special care must be taken during installation. To install, twist the
ring sideways just enough to get it around the shaft or sleeve. Do not attempt to pull rings straight out.
See image below. Another form of packing ring is the bulk-type packing which is cut to the proper length.
Each piece should be placed around the shaft or sleeve and the ends of the packing should just meet to
form a smooth, perfect ring. If necessary, the ends should be trimmed to obtain this fit.

Figure 36: Correct

Figure 37: Incorrect

There are two basic types of lantern rings - PTFE and metal. Two-piece PTFE lantern rings are supplied
in most units. Install as shown below. Note: 2 pieces make one ring. Notches must face one another but
need not be aligned.

Correct

Incorrect

Figure 38: Metal Lantern Ring

Figure 39: PTFE Lantern Ring

To pack the stuffing box, install the packing and lantern ring in the proper sequence. Each ring should be
installed separately. Firmly seat each ring. Use of a wooden split bushing is recommended. See image

5.4 Stuffing Box Packing

34

3175 Installation, Operation and Maintenance Instructions

«
...
34
35
36
37
38
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: vacuubrand Страницы: 44

Бренд: Quooker Страницы: 12

Бренд: salmson Страницы: 16

Бренд: Davey Страницы: 4

Бренд: SMC Networks Страницы: 19

Бренд: Barracuda PUMPS Страницы: 4

Бренд: Speck Страницы: 24

POWERplus POWX1700

Бренд: VARO Страницы: 10

Бренд: Leader Pumps Страницы: 8

Бренд: Ocean Technologies Страницы: 2

FXV-1212C-32Q-M/Q

Бренд: BAC Страницы: 47

Бренд: Graco Страницы: 20

Бренд: Bard Страницы: 24

Бренд: Wijas Страницы: 12

Бренд: Grundfos Страницы: 42

Бренд: Immergas Страницы: 18

Boiler Performance BOSS 36

Бренд: Manta Страницы: 4

Бренд: Yale Страницы: 130

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды