ITT Goulds Pumps 3175 Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 87

background image

6.2 Lubricate the Pump

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure

bearings are properly lubricated prior to startup.

1.

Oil Lubrication

Refer to

5.2 Pump Bearings on page 32

for oil specifications. Oil lubricated ball bearings are stand-

ard on the Model 3175. The bearings are not lubricated at the factory.

Oil lubricated pumps are supplied with an oiler which maintains a constant oil level in the bearing
frame. Refer to

6.5 Disassemble the Pump on page 56

for oiler location.

a) Before installing the oiler on the bearing frame, check the oiler adjustment.

1 - Oil level

Figure 50: Oiler

Instructions

i.

Remove adjustment assembly from oiler

ii.

Adjust bars to 9/16"

iii.

Lock in position

iv.

Replace adjustment assembly in oiler

b) Install oiler on either side near oil level groove marked on frame.

c)

Fill the oiler bottle with oil and replace in the oiler housing. Oil reservoir in bearing frame is filled
when oil remains visible in the bottle. Several fillings of the bottle will be required. Never fill
through the oil vent or the oiler without use of the bottle.

For information only: The Model 3175 bearing frame oil capacities are:

Group

Approx. Capacity

S

167 oz | 5 Qts.

M

133 oz | 4 Qts.

L

100 oz | 3 Qts.

2.

Grease Lubrication - To lubricate pump: Insert grease through grease fittings while shaft is rotating,
until dean grease appears through the relief caps.

6.2 Lubricate the Pump

3175 Installation, Operation and Maintenance Instructions

51

«
...
51
52
53
54
55
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: Eaton Страницы: 12

Бренд: wallas Страницы: 109

Бренд: Kaisai Страницы: 40

Water Jet Lightning

Бренд: Oase Страницы: 28

AquaMax Eco Premium 4000

Бренд: Oase Страницы: 120

Бренд: Oase Страницы: 9

Бренд: Valeo Страницы: 88

Бренд: Valdemar Energy Страницы: 61

Бренд: TradeQuip Страницы: 8

Omnivore XLSG200 Series

Бренд: Liberty Pumps Страницы: 12

VeroLine-IPS 20

Бренд: Wilo Страницы: 42

Бренд: Gardena Страницы: 10

Бренд: Mueller Страницы: 46

Бренд: Gorenje Tiki Страницы: 48

Бренд: Econo Страницы: 27

Бренд: Edwards Страницы: 60

Fre-Heater D Series

Бренд: Mueller Страницы: 34

Copper Cricket 1B

Бренд: Sage Advance Corp Страницы: 67

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды