ITT Goulds Pumps 3175 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 87

background image

1. Dam

5. Bedplate

2. Wedges

6. Grout

3. Leave 3/4" to 1-1/2" under bedplate for grout

7. Leave top of foundation rough and wet
before grouting

4. Waste

8. Concrete foundation

Figure 10: Concrete Foundation

The I. D. of the sleeve should be 2 1/2 - 3 times the bolt diameter.

b) Stuff waste around bolts to prevent concrete from entering between bolt and sleeve. Bolts

should be of sufficient length so that they project through the nuts approximately 1/4" after al-
lowance has been made for grouting, bedplate thickness, and nut thickness.

NOTICE:

Remove all dirt from the mounting pads in order to ensure that the correct leveling is achieved.
Failure to do so can result in equipment damage or decreased performance.

3.

Put the unit in place on wedges. The wedges should be placed at four points as shown in the image
below. Some long installations may require additional wedges near the middle of the bedplate.

1. Wedges

2. Foundation

Figure 11: Wedge placement

4.

Disconnect coupling between pump and driver.

4.4 Install Horizontal Pumps

18

3175 Installation, Operation and Maintenance Instructions

«
...
18
19
20
21
22
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: Paloma Страницы: 24

Бренд: Raypak Страницы: 40

Бренд: Samoa Страницы: 40

Бренд: Watson Marlow Pumps Страницы: 95

Бренд: Watson Marlow Pumps Страницы: 87

Бренд: Watson Marlow Pumps Страницы: 127

Бренд: ubbink Страницы: 31

Бренд: Graco Страницы: 48

Бренд: Reefe Страницы: 12

Бренд: Davey Страницы: 20

Бренд: Bryant Страницы: 4

Бренд: A.O. Smith Страницы: 4

Бренд: German pool Страницы: 20

Бренд: Pfeiffer Vacuum Страницы: 60

Бренд: Samoa Страницы: 40

MD 12C NT VARIO o.C.

Бренд: vacuubrand Страницы: 92

Бренд: AME Страницы: 6

Бренд: Homelite Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды