ITT Goulds Pumps 3175 Скачать руководство пользователя страница 11

Страница: 11 / 87

CSA certification

Intrinsically safe for:

•

Class I, Div. 1, Groups A, B, C, D

•

Class II, Div. 1, Groups E, F, G

•

Class III

•

Certified to Canadian and US requirements

SERIAL NO. & YEAR OF
MANUFACTURE HERE.

1.1.4 Product warranty

Coverage

ITT undertakes to remedy faults in products from ITT under these conditions:

•

The faults are due to defects in design, materials, or workmanship.

•

The faults are reported to an ITT representative within the warranty period.

•

The product is used only under the conditions described in this manual.

•

The monitoring equipment incorporated in the product is correctly connected and in use.

•

All service and repair work is done by ITT-authorized personnel.

•

Genuine ITT parts are used.

•

Only Ex-approved spare parts and accessories authorized by ITT are used in Ex-approved prod-
ucts.

Limitations

The warranty does not cover faults caused by these situations:

•

Deficient maintenance

•

Improper installation

•

Modifications or changes to the product and installation made without consulting ITT

•

Incorrectly executed repair work

•

Normal wear and tear

ITT assumes no liability for these situations:

•

Bodily injuries

•

Material damages

•

Economic losses

Warranty claim

ITT products are high-quality products with expected reliable operation and long life. However, should
the need arise for a warranty claim, then contact your ITT representative.

1.1 Introduction and Safety

3175 Installation, Operation and Maintenance Instructions

Содержание Goulds Pumps 3175
























































































Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды

ITT Goulds Pumps 3175, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание Goulds Pumps 3175

Отзывы:

Похожие инструкции для Goulds Pumps 3175

Бренды по названию

Популярные бренды