ITT Goulds Pumps 3175 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 87

background image

NOTICE:

•

Verify the driver settings before you start any pump. Refer to the applicable drive equip-
ment IOMs and operating procedures.

•

Excessive warm-up rates can cause equipment damage. Ensure the warm-up rate does
not exceed 1.4°C | 2.5°F per minute.

•

The mechanical seal used in an Ex-classified environment must be properly certified.

NOTICE:

You must follow these precautions before you start the pump:

•

Flush and clean the system thoroughly to remove dirt or debris in the pipe system in order
to prevent premature failure at initial startup.

5.2 Pump Bearings

Oil Lubrication

WARNING:

Risk of explosive hazard and premature failure from sparks and heat generation. Ensure

bearings are properly lubricated prior to startup.

Oil lubricated pumps are not lubricated at the factory. A high quality turbine type oil, with rust and oxida-
tion inhibitors, should be used. Constant level oilers are supplied with most oil lubricated pumps. They
are included in the box of fittings which accompanies the pump. The oiler was adjusted to maintain prop-
er oil level before leaving the factory. The adjustment should be checked in case this setting was distur-
bed. See image below. Check the assembly dimension print for proper location.

1 - Oil level

Figure 35: Oiler

Instructions

1.

Remove adjustment assembly from oiler

2.

Adjust bars to 9/16"

3.

Lock in position

4.

Replace adjustment assembly in oiler

5.2 Pump Bearings

32

3175 Installation, Operation and Maintenance Instructions

«
...
32
33
34
35
36
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: RBI Страницы: 48

Бренд: Immergas Страницы: 40

Бренд: Mannesmann Страницы: 3

Бренд: Barnes Страницы: 16

Бренд: Naked Страницы: 12

LARIUS SIRIO 60:1

Бренд: Samoa Страницы: 46

Бренд: DAYLIFF Страницы: 8

Бренд: Malmbergs Страницы: 12

Бренд: Anest Iwata Страницы: 4

Бренд: OilGear Страницы: 31

Duraclad Lime Tamer

Бренд: A.O. Smith Страницы: 2

Бренд: Zip Страницы: 24

TurboSilence InverX IXCR36

Бренд: Fairland Страницы: 117

Бренд: Nakayama Страницы: 29

Бренд: TCM Страницы: 127

Бренд: Samoa Страницы: 10

Бренд: Drummond Страницы: 12

PWS BEV-300 Series

Бренд: Pure Water Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды