ITT Goulds Pumps 3175 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 87

background image

6.3 Impeller Clearance Adjustment

WARNING:

Failure to disconnect and lock out driver power may result in serious physical injury or death.
Always disconnect and lock out power to the driver before performing any installation or main-
tenance tasks.

•

Electrical connections must be made by certified electricians in compliance with all inter-
national, national, state, and local rules.

•

Refer to driver/coupling/gear manufacturer's installation and operation manuals (IOM) for
specific instructions and recommendations.

The impeller clearance setting procedure must be followed. Improperly setting the clearance

or not following any of the proper procedures can result in sparks, unexpected heat generation,
and equipment damage.

If a gradual loss in head and/or capacity occurs, performance can be restored by adjusting the impeller. If
performance cannot be restored by adjustment, pump should be disassembled as directed in

semble the Pump on page 56

and the impeller and casing inspected for wear.

Either a feeler gauge or a dial indicator can be used to set the impeller clearance.

Feeler Gauge Method

1.

Loosen adjustment bolts and nuts (371A & 423B).

2.

Tighten bolts (370C) evenly, while slowly rotating the shaft, until the impeller just starts to rub on
the casing.

3.

Loosen each bolt (370C) until a 0.38 mm | .015" feeler gauge can be placed between the bearing
housing flange and underside of head of bolts (370C).

4.

Be sure that jam nuts on bolts (371A & 423B) are loose. Tighten each bolt (371A & 423B) a flat at
a time until bearing housing is tight against bolts (370C). Be sure that all bolts (370C, 371A &
423B) are tight. Tighten jam nuts on bolts (371A & 423B).

6.3 Impeller Clearance Adjustment

3175 Installation, Operation and Maintenance Instructions

53

«
...
53
54
55
56
57
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: Gardena Страницы: 182

Бренд: Waterstone Страницы: 6

BURKAY 102 Series

Бренд: A.O. Smith Страницы: 24

Бренд: Tandem Страницы: 120

Бренд: YAMADA Страницы: 14

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: KNF Страницы: 22

Бренд: TOHATSU Страницы: 87

Бренд: Naked Страницы: 12

Бренд: Bock Water heaters Страницы: 62

Бренд: C.P.A. Страницы: 40

Бренд: Wilden Страницы: 39

Бренд: Truma Страницы: 36

Бренд: Enviro Страницы: 112

VITOCAL 300-G PRO Type BW 2150

Бренд: Viessmann Страницы: 124

Бренд: DAB PUMPS Страницы: 200

Бренд: Peraqua Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды