ITT Goulds Pumps 3175 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 87

background image

NOTICE:

This is an initial alignment. The final alignment is done after the unit has been run under actual
operating conditions. The final alignment procedure is outlined in

5.18 Final Alignment on page

and must be followed. Make sure: motor starting switch is "locked out" to prevent acciden-

tal rotation.

Any coupling manufacturer's instruction sheets, sent with the pump, should be studied and used when
installing, aligning, or servicing coupling. Note that coupling hubs are not necessarily mounted flush with
the shaft ends.

If instructions are not available, the following procedure may be used. The procedure is given for two ba-
sic coupling types:

1.

Flexible Coupling - Normally furnished on all units except "back pull-out". Normally not assem-
bled (except "spider-insert" type which are preassembled) .

2.

Flexible Spacer Coupling - Furnished as standard on all "back pull-out" units. Contains a remova-
ble spacer piece located between coupling hubs.

NOTICE:

Note that alignment in one direction may alter alignment in another. Check through each align-
ment procedure after making any alignment alteration.

4.5.1.1 Parallel Alignment

1.

Unit is in parallel misalignment when the shaft axes are parallel but not concentric. Shift driver as
required.

2.

In order to obtain vertical parallel alignment under actual operating conditions, the driver shaft may
have to be set higher or lower (using thin shim stock) than the pump shaft due to differences in ex-
pansion rates. Pump expansion rates vary with pump design. The following is a suggested cold set-
ting for motor driven units:

Figure 13: Frame Mounted Units

Option

Description

Pumpage Temperature

Set

Above Ambient

Motor

Temperature

Shaft

Option

Description

Ambient

0.102mm - 0.152mm | 0.004" - 0.006" Low

38°C | 100°F

0.051mm - 0.102mm | 0.002" - 0.004" Low

93°C | 200°F

0.000mm - 0.051mm | 0.000" - 0.002" Low

149°C | 300°F

0.000mm - 0.051mm | 0.000" - 0.002" High

4.5 Pump-to-driver alignment

20

3175 Installation, Operation and Maintenance Instructions

«
...
20
21
22
23
24
...
»

Содержание Goulds Pumps 3175
























































































Отзывы:

Нет отзывов

Похожие инструкции для Goulds Pumps 3175

Бренд: Panasonic Страницы: 55

Бренд: AromaMist Страницы: 15

Бренд: Daikin Страницы: 30

Бренд: Pentair Pool Products Страницы: 2

Бренд: Amana Страницы: 26

Бренд: Larzep Страницы: 14

Бренд: Milton Roy Страницы: 43

Бренд: IBAIONDO Страницы: 7

Бренд: Varian Страницы: 44

Tranquility TR Series

Бренд: ClimateMaster Страницы: 96

Бренд: samhydraulik Страницы: 7

ACT Signature Series

Бренд: Aqua Comfort Страницы: 2

POOLEX JETLINE SELECTION FI

Бренд: poolstar Страницы: 7

Бренд: DAE Pumps Страницы: 29

Бренд: AL-KO Страницы: 186

Бренд: intensity Страницы: 23

Бренд: red lion Страницы: 8

Бренд: C.P.A. Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды